24
2020
-
11
Talk about the role of some parts in the setting machine
Author:
We know that during the operation of the setting machine, three important process requirements need to be reasonably controlled, namely temperature, time and pressure. In the tenter drying room, if it is found that the insulation layer of the drying room needs to be replaced or scrapped, the insulation materials filled in it shall be disposed or destroyed according to the relevant local environmental protection regulations. As for the temperature control of the drying room, the process temperature is mainly set by the up and down keys on the temperature control table.
We know that during the operation of the setting machine, three important process requirements need to be reasonably controlled, namely temperature, time and pressure. In the tenter drying room, if it is found that the insulation layer of the drying room needs to be replaced or scrapped, the insulation materials filled in it shall be disposed or destroyed according to the relevant local environmental protection regulations. As for the temperature control of the drying room, the process temperature is mainly set by the up and down keys on the temperature control table.
In the tenter setting machine equipment in the tenter drying room is also equipped with the corresponding burner, mainly to play the role of heating the drying room. The temperature control instrument controls the flame size to control the temperature. Contactor control logic start-stop. The operation steps of the burner are as follows: first turn on the circulating fan, then turn on the key switch of the burner to allow the burner to work; Turn on the main engine and keep the vehicle speed above 5 m/min; After that, set the process temperature on the temperature control meter. The burner is finished.
The next step is to enter the link of air cooling out of the cloth, mainly to achieve the requirements of rapid cooling of the fabric. However, in the tail box of the tenter setting machine equipment, the main operation contents include: adjusting the needle removal position and lowering the roller when the cloth is drawn through the tail outlet roller; Set the process parameters (host speed) on the man-machine interface; Turn on the main engine and run the tail outlet rolling car; Check the lubricating oil quality and oil quantity of the transmission box of the main engine according to the regulations, and lubricate the tail amplitude modulation screw rod according to the regulations.
It should be noted that at the end of the work, the site staff should be appropriate to adjust the tenter setting machine tail out of the tail of the cloth roller cylinder nut, in order to keep the upper roller in a separate position. The main function of the surface winding is the finished fabric winding, suitable for the speed of 2~20 m/min.
In the setting machine winding, you can use different ways, such as manual, stop, automatic three states. When manual, the vehicle speed is not controlled with the line speed of the host, and the operator can set the speed at will; when automatic, the line speed is slightly faster than the host, and the tension of the cloth surface is adjusted by adjusting the winding speed. When stopped, the winding stop action.
24
2020-11
Talk about the role of some parts in the setting machine
We know that during the operation of the setting machine, three important process requirements need to be reasonably controlled, namely temperature, time and pressure. In the tenter drying room, if it is found that the insulation layer of the drying room needs to be replaced or scrapped, the insulation materials filled in it shall be disposed or destroyed according to the relevant local environmental protection regulations. As for the temperature control of the drying room, the process temperature is mainly set by the up and down keys on the temperature control table.
25
2020-11
Reliable technical services for customers, full guidance and training.
25
2020-11
Raw material warehousing services
The company creates a high-level, high-level, high-level warehouse management environment with advanced management experience for customers.
25
2020-11
The company has a group of skilled and experienced mold design engineers, NC design engineers, mold production master. Specializes in complex, precision, large mold design and manufacturing.
25
2020-11
Yibao was established in 2002. The company's main business is to provide a complete set of solutions for industrial and service industries: industrial production automation, integration, industrial production cloud data, etc., to provide customers with talent consultation and technology output, automation equipment output, and customers The main targets are Southeast Asian countries: Vietnam, Bangladesh, Lanca, Indonesia, Mexico, etc......
25
2020-11
Yibao Industrial Underwear Mold Cup One-stop Service Solution
25
2020-11
Yibao Industrial Underwear Mold Cup One-stop Service Solution
Address:
Bergang, Xiaojinkou, Huicheng District, Huizhou City, Guangdong Province, China
Mobile:
86 752 2063598
E-mail:
xusun@hzyibao.cn
Business License